eken-m002-boot-log
this log has been pruned for serial numbers, mac address, and any other personal info.
WonderMedia Technologies, Inc.
W-Load Version : 0.19.00.03
ethaddr............found


U-Boot 1.1.4 (Nov  6 2010 - 12:28:29)
WonderMedia Technologies, Inc.
WMT U-Boot Version : 0.12.01.00.34
U-Boot code: 03F80000 -> 03FCD458  BSS: -> 0401EA74
RAM Configuration:
Bank #0: 00000000 128 MB
boot from spi flash.
flash:
     Bank1: FFF80000 -- FFFFFFFF
     Bank2: FF780000 -- FFF7FFFF
Flash:  8.5 MB
In:    serial
Out:   serial
Err:   serial
logocmd="lcdinit2;cp.b fffd0000 100000 10000;decompanima -s 0x100000 0x3000000 0x4000000 0x7d00000;lightlcd;run 
text1;usbinit"
LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13
PWM param (setting): 0,4,599,599
LCD FrameBuffer = 0x07900000, BMP Address = 0x03C00000
LCD init OK
small log cp***
LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13
PWM param (setting): 0,4,599,599
PWM0 input freq = 47916666 Hz, output freq = 19998 Hz
PWM0 register setting: scalar = 3, period = 598, duty = 598
"Android2.2"
usb usb1: Product: USB Host Controller
usb usb1: Manufacturer: Linux 2.6.10_dev-VT8610 ehci_hcd
usb usb1: SerialNumber: pci-echi
 1-0:1.0: USB hub found
 1-0:1.0: 2 ports detected
locktree(): line: 1024: this function not completed
usb 1-: new high speed USB device using abc and address 2
usb 1-: Product: Flash Disk
usb 1-: Manufacturer: Generic
usb 1-: SerialNumber: REMOVEDFROMLOG
       scanning bus for storage devices... part_offset : 3f, cur_part : 1
1 Storage Device(s) found
usb 1-+11111111010101: new high speed USB device using abc and address 3
usb 1-+11111111010101: Product: USB2.0 Hub
       scanning bus for storage devices... 1 Storage Device(s) found
REG32_VAL(0xd8000440) = 0x08080800
memory size: 128MB
### main_loop entered: bootdelay=1

Execute register operation:
  reg op: 0xD8110064 | 0x4
  reg op: 0xD811008C | 0x4
  reg op: 0xD81100B4 & 0xFFFFFFFB
  reg op: 0xD8110064 | 0x8
  reg op: 0xD811008C | 0x8
  reg op: 0xD81100B4 | 0x8
  reg op: 0xD8130054 | 0x1
### main_loop: bootcmd="fatload usb 0 7c00000 animation.data;fatload usb 0 0 uzImage.bin;bootm 0"
Hit Enter key to stop autoboot:  0
ATSMB Host 390KHz
SD Card is not inserted
part_offset : 3f, cur_part : 1
reading animation.data
Tina_Match: isdir 0x0######################
mydata :
Size of clusters in sectors : 4
The sector of the first cluster, can be negative : 97
Current FAT buffer : 03f4d6fc
fatbufnum : ffffffff
Length of FAT in sectors : 3f
Size of FAT in bits : 10
Starting sector of the FAT : 1
Start sector of root directory : 7f
.

0x20644 bytes read
part_offset : 3f, cur_part : 1
reading uzImage.bin
Tina_Match: isdir 0x0######################
mydata :
Size of clusters in sectors : 4
The sector of the first cluster, can be negative : 97
Current FAT buffer : 03f4d6fc
fatbufnum : ffffffff
Length of FAT in sectors : 3f
Size of FAT in bits : 10
Starting sector of the FAT : 1
Start sector of root directory : 7f
..........................

0x297DE8 bytes read
## Booting image at 00000000 ...
   Image Name:   MontaVista Linux 2.6.10
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2719144 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 00008000) ...

Starting kernel ...

Uncompressing 
Linux............................................................................................................................................................................ 
done, booting the kernel.
Linux version 2.6.29-00236-g4f8dbbb-dirty (howayhuo@szmce12) (gcc version 4.2.0 20070126 (prerelease) (MontaVista 
4.2.0-3.0.0.0702771 2007-03-10)) #59 Mon Nov 8 17:25:11 HKT 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: WMT
Memory policy: ECC disabled, Data cache writethrough
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 27686
Kernel command line: mem=109M noinitrd root=/dev/sda5 rootfstype=ext3 rw console=ttyS0,115200n8 init=/init lcdid=1 
androidboot.console=ttyS0 loadtime=-3 rootdelay=7
[LCD] lcd_arg_panel_id: <6>set lcd panel id = 1
Unknown boot option `androidboot.console=ttyS0': ignoring
set load time = -3
PID hash table entries: 512 (order: 9, 2048 bytes)
start_kernel(): bug: interrupts were enabled early
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 109MB = 109MB total
Memory: 104476KB available (5048K code, 775K data, 144K init)
Calibrating delay loop... 174.48 BogoMIPS (lpj=872448)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 520 bytes
NET: Registered protocol family 16
wmt_init
wmt_pci_init
PCI: WonderMidia Technology PCI Bridge
PCI: bus0: Fast back to back transfers disabled
[WMT-MB] Preparing VIDEO BUFFER (SIZE 16384 kB) ...
[WMT-MB] MAX MB Area size: Max 4096 Kbs Min 256 Kbs
[WMT-MB] prob /dev/Memory Block major 216, minor 0
mb_init ok
bio: create slab  at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
VT8500 SPI Flash Driver, (c) 2007 VIA Electronics ltd.
Find SPI Flash, ID = 0x001C3113
Find SPI Flash, ID = 0x00000000
un-know id = 0x0
vt8500 sf controller initial ok
cmdlinepart partition parsing not available
Creating 6 MTD partitions on "mtdsf device":
0x000000000000-0x000000d00000 : "filesystem-SF"
0x000000d00000-0x000000f80000 : "kernel-SF"
0x000000f80000-0x000000fd0000 : "u-boot-SF"
0x000000fd0000-0x000000fe0000 : "u-boot logo"
0x000000fe0000-0x000000ff0000 : "u-boot env. cfg. 1-SF"
0x000000ff0000-0x000001000000 : "w-load-SF"
ashmem: initialized
yaffs Nov  8 2010 17:21:11 Installing.
msgmni has been set to 204
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
loadtime = -3
start_boot_splash: screen xres = 800, yres = 480
processbar gefb: framebuffer at 0x7d00000, mapped to 0xc7400000, using 3072KB, total 3072KB
--> framebuffer is right
--> animation_start ok
vpp_init(boot logo 1)
-------------lcd_init
kmalloc buffer env_ptr = 0xc6920000, env_ptr_nand = 0xc6920000
--- pwmparam = 0,4,599,599
pwm_no = 0 scalar = 4, period = 599, duty = 599
pwm0: clock = 47916666, freq = 19998, level = 100
[VOUT] DVO to LCD
[LCD Type] CHILIN LW700AT9003
fb0: WMT GE frame buffer device
fb1: WMT VPU frame buffer device
------------ pwm_init
## Warning: "vibratorset" not defined
Error when reading vibratorset from u-boot!!!
WMT vibrater driver load successfully!
uart.0: ttyS0 at MMIO 0xd8200000 (irq = 32) is a wmt serial
uart.1: ttyS1 at MMIO 0xd82b0000 (irq = 33) is a wmt serial
uart.2: ttyS2 at MMIO 0xd8210000 (irq = 47) is a wmt serial
uart.3: ttyS3 at MMIO 0xd82c0000 (irq = 50) is a wmt serial
uart.4: ttyS4 at MMIO 0xd8370000 (irq = 31) is a wmt serial
uart.5: ttyS5 at MMIO 0xd8380000 (irq = 30) is a wmt serial
WMT Serial driver initialized: ok
brd: module loaded
loop: module loaded
nbd: registered device at major 43
--> pmem_init
pmem: 0 init
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v0.1.0)
[wmt-vd] prob /dev/wmt-vd major 236, minor 0, prdt ffc01000/6960000, size 100 KB
[wmt-vd] WonderMedia HW decoder driver inited
st: Version 20081215, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
NAND Driver, (c) 2008 WMT Electronics ltd.
1PMNAND_ADDR=0x10c
nand chip device maf_id is 0, and dev_id is 0
nand chip device maf_id is 0, and dev_id is 0
No NAND device found!!!
## Warning: "nand_chip_num" not defined
MTD NADN flash driver probe default 1 chip
No NAND device found!!!
nand initialised ok
spi_probe: /dev/WMT_SPI major number 154, minor number 0, device number 3
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: enabling device 0000:00:04.0 (0040 -> 0042)
ehci_hcd 0000:00:04.0: EHCI Host Controller
ehci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:04.0: irq 1, io mem 0xd8007100
ehci_hcd 0000:00:04.0: USB 0.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29-00236-g4f8dbbb-dirty ehci_hcd
usb usb1: SerialNumber: 0000:00:04.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PCI: enabling device 0000:00:05.0 (0000 -> 0001)
uhci_hcd 0000:00:05.0: UHCI Host Controller
uhci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:05.0: irq 0, io base 0xd8007300
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-00236-g4f8dbbb-dirty uhci_hcd
usb usb2: SerialNumber: 0000:00:05.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
## Warning: "3g_powerup" not defined
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver VIAUSBModem
LinuxVIAUSBD1.0.4:VIA USB CDMA Modem<6>USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
udc: VIA UDC driver, version: 3 December 2007 (dma)
udc: pullup_disable()
IRQ 5/wmotgdev: IRQF_DISABLED is not guaranteed on shared IRQs
IRQ 2/wmotgdev: IRQF_DISABLED is not guaranteed on shared IRQs
udc: wmt_udc_probe - request_irq(0x05) pass!
i8042_controller_init
I8042_CMD_CTL_TEST ok 0x55
write 0x50 cmd 0x1060
serio: i8042 AUX port at 0xd8008800,0xd8008804 irq 4
serio: i8042 KBD port at 0xd8008800,0xd8008804 irq 23
mice: PS/2 mouse device common for all mice
wmt_rtc on
wmt-rtc wmt-rtc.0: rtc core: registered wmt-rtc as rtc0
WMT Real Time Clock driver v0.54 initialized: ok
i2c /dev entries driver
i2c: adding wmt_i2c_adapter.
i2c: successfully added bus
[wmt_i2c_api_i2c_init]
[wmt_i2c_api_init] wmt_i2c_api_init.
i2c: wmt algorithm module loaded.
Bluetooth: Generic Bluetooth USB driver ver 0.5
usbcore: registered new interface driver btusb
sd power down
## Warning: "sd_powerdown" not defined
WMT AHB to SD/MMC bus controller registered!
------------ lcd_backlight_init
Registered led device: lcd-backlight
atkbd.c: keyboard reset failed on isa0060/serio1
sd power up
## Warning: "sd_powerup" not defined
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.18a.
Sound: WMT AC97: dsp id 3 mixer id 0
## Warning: "audio_max_gain" not defined
Max. audio gain was default value(0x1e)
## Warning: "wmt_disspdif" not defined
VT1613 generic driver installed
ALSA device list:
  No soundcards found.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Trying to free already-free IRQ 4
Trying to free already-free IRQ 4
Bluetooth: RFCOMM socket layer initialized
rfcomm_init_ttys: Can't register RFCOMM TTY driver
Bluetooth: RFCOMM ver 1.11
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
atkbd.c: keyboard reset failed on isa0060/serio0
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear 
All bugs added by David S. Miller 
## Warning: "vibra_enable" not defined
## Warning: "pwbtn" not defined
input: kpadPower as /devices/virtual/input/input0
PMC: WonderMedia Power Management driver
PMC: Power button is configured as soft power
VFP support v0.3: not present
wmt-rtc wmt-rtc.0: setting system clock to 2000-01-01 00:32:50 UTC (946686770)
Waiting 7sec before mounting root device...
Trying to free already-free IRQ 23
atkbd.c: keyboard reset failed on isa0060/serio1
usb 1-1: new high speed USB device using ehci_hcd and address 2
Trying to free already-free IRQ 4
atkbd.c: keyboard reset failed on isa0060/serio0
Trying to free already-free IRQ 23
Trying to free already-free IRQ 4
usb 1-1: New USB device found, idVendor=1e3d, idProduct=2095
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Flash Disk
usb 1-1: Manufacturer: Generic
usb 1-1: SerialNumber: REMOVEDFROMLOG
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: New USB device found, idVendor=05e3, idProduct=0608
usb 1-2: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-2: Product: USB2.0 Hub
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
sd power down
[GOVRH] VGA DAC DISCONNECT
scsi 0:0:0:0: Direct-Access     Generic  Flash Disk       5.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 4157440 512-byte hardware sectors: (2.12 GB/1.98 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 4157440 512-byte hardware sectors: (2.12 GB/1.98 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda5, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) on device 8:5.
Freeing init memory: 144K
Warning: unable to open an initial console.
init: /init.rc: 399: invalid option '-n'
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda6, internal journal
EXT3-fs: sda6: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on sda7, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
[get_specialkpad]: find uboot arg kpadid=m001v2_4 !!!!!!!!
[kpadall_probe]: kpadname: m001v2,  keycodenum:8!!!
input: kpad as /devices/virtual/input/input1
[kpadall_probe]: registered irq: 8 ***
drivers/input/touchscreen/wm9715-api.c 332
init: vt1613_ref=0
drivers/input/touchscreen/wm9715-api.c 335
## Warning: "touchcodec" not defined
## Warning: "lowalarmcfg" not defined
audioic = 0
BASEVOLT = 3000
preparecnt = 0
## Warning: "touchcodec" not defined
touchirq = 4!panelres.x = 800, panelres.y = 480!<6>input: touchscreen as /devices/virtual/input/input2
wm9715 ts driver init ok!
get the sensor config:0,-1,1,1,2,1**********
gsensor interrupt:gpio6 ******************
mma7660A compass driver: init
mma7660_probe&&&&&&&&&&&&&&&&&&&&&&&
input: compass as /devices/virtual/input/input3
VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.13
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
Copyright (c) 2004 Red Hat Inc.
eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
eth0: Ethernet Address: 00:40:63:EA:93:15
init: cannot find '/system/bin/playmp3', disabling 'bootsound'
init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
init: cannot find '/system/bin/telnetd', disabling 'telnetd'
warning: `adbd' uses 32-bit capabilities (legacy support in use)
localhost login: --- fsg_bind, mod_data.nluns = 0
is WonderMedia Technology
Shake enable!!
usb_mass_storage gadget: File-backed Storage Gadget, version: 20 October 2004
usb_mass_storage gadget: Number of LUNs=2
udc: pullup_enable()
preparecnt = 1
amp power down
--wmt_audio_init
init: vt1613_ref=1
pcmvolum:puzhi
set pcm volume successfully for puzhi!
## Warning: "hpvolum" not defined
## Warning: "spkvolum" not defined
Audio Line In
wm9715_gpioirq_adcandpen
audio_mic_mute enable
## Warning: "amp_stop_when_nouse" not defined
SNDCTL_DSP_SETFMT, val = 0x10
SNDCTL_DSP_CHANNELS, value= 2
SNDCTL_DSP_SPEED, val=44100
audio_discard_buf
audio_setup_dma s->direction = 0, byte =2, channel = 1
audio_discard_buf
audio_setup_dma s->direction = -1, byte =2, channel = 2
SOUND_MIXER_VOLUME. volume val = 100
left = 0x0000, right = 0x0000
## Warning: "enable_hw_scal" size(2) exceed buffer size(0)
[WMT-MB] mb driver is opened by task thumbserver TGID 53.
[WMT-MB] mb driver is closed by task thumbserver TGID 53.
pmem: pid 0, allocate 1000000
the curr is 0, and allocate order is c, and curr order is c
ioctl VPPIO_VPPSET_DIRECTPATH!!!!!!!!!!
ioctl VPPIO_VPPSET_DIRECTPATH end!!!!!!!!!!
[LCD Type] CHILIN LW700AT9003
[LCD] CHILIN LW700AT9003 (id 1,bpp 24)
lcd_lw700at9003_initial
procfile_write get 0

[WMT-MB] mb driver is opened by task mediaserver TGID 58.
## Warning: "restore_byandroid" not defined
request_suspend_state: wakeup (3->0) at 59811606002 (2000-01-01 00:33:48.604033000 UTC)
## Warning: "wmt_rotation" not defined
[WMT-MB] mb driver is opened by task InputDeviceRead TGID 121.
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
## Warning: "wmt_rotation" not defined
SOUND_MIXER_VOLUME. volume val = 80
left = 0x0000, right = 0x0000
SOUND_MIXER_VOLUME. volume val = 100
left = 0x0000, right = 0x0000
Velocity is AUTO mode

Login timed out after 60 seconds
localhost login: ---- audio write: s->active = 0
amp power up
wm9715 ts driver v1.3 opening...
wm9715_ts_ioctl: TS_IOCTL_CAL_DONE
g_CalcParam = 345, -23358, 92425656, 14526, 270, -2992120, 111887

Login timed out after 60 seconds
localhost login: pmc_wakeup_isr: power key pressed
bit14 is cleaned
kpadPower_timeout: power key released
request_suspend_state: wakeup (0->0) at 152981643002 (2000-01-01 00:35:21.774068000 UTC)
pmc_wakeup_isr: power key pressed
request_suspend_state: wakeup (0->0) at 162636395002 (2000-01-01 00:35:31.428822000 UTC)
## Warning: "skip_screenlock" not defined
bit14 is cleaned
kpadPower_timeout: power key released
pmc_wakeup_isr: power key pressed
bit14 don't clean
bit14 don't clean
bit14 don't clean
bit14 don't clean
bit14 don't clean
bit14 is cleaned
kpadPower_timeout: power key released
-------------------- do set config
udc: pullup_disable()
Power down.
wmt_power_off